DEEPCOOL - Dispositivo di raffreddamento per CPU Assassin Ii 8 HEAT PIPES

Ottimo dissipatore, molto efficiente.
La prima cosa che mi ha stupito è la grandezza, entra precisamente nel mio case Cooler Master HAF-X Full Tower e non sarebbe entrato in uno più piccolo.
Questo fantastico dissipatore garantisce ottime temperature sul mio Intel Core i7 5820K che rimane sempre sulla media dei 40-50°C,
accettabilissima.
Consiglio a chi ha un qualunque processore (anche AMD) che in futuro andrà overcloccato.

3 persone l'hanno trovato utile

Rio

Da non perdere

Recensito in Italia il 7 gennaio 2018

pacchettato molto bene mi é piaciuto il prodotto
trasporto abbastanza veloce
solamente ho comorato middle tower che é troppo piccolo per questo prodotto

davvero una bestia di dissipatore! Rendimento solo di poco inferiore al top di settore.

Totocellux

Recensito in Italia il 10 settembre 2019

acquistato direttamente dal produttore (DeepCool) ad un prezzo irrisorio. Non è ciò che si può dire un peso piuma, ma il livello costruttivo è alto, facendomi guadagnare, in full-load, ~9°C rispetto ad un già meritevole Scythe Mugen2 rev.B. Il mio Intel i7-6700k (oc @4.8GHz) ne sta beneficiando in longevità di vita operativa. Ottimo prodotto anche al suo normale costo, di circa 70€. Devo dire che non mi aspettavo un prodotto di questa resa da parte di DeepCool. Consigliato.

Una persona l'ha trovato utile

Ottimo, dissipa benissimo, ma...

fabrizio bonfanti

Recensito in Italia il 24 agosto 2018

Ottimo, dissipa benissimo, ma... state attenti, è piottosto ingombrante, in molti cases non ci sta, e se avete RAM ad alto profilo è un po' un problema

Traduci tutte le recensioni in Italiano

Le recensioni migliori da altri paesi

Tastentester

Rund 25% mehr Leistung bei i7 3770k möglich, groß und leise

Recensito in Germania il 8 gennaio 2018

Rund 25% mehr Leistung bei i7 3770k möglich, groß und leise

Ich nutze den ASSASSIN II, also das größte momentan verfügbare Modell für aktuell 70€ (Blitzangebot 48€).

Achtung: Der Kühler ist ein Riesending, was gerade so in einen normalen Midi Tower passt. Ich nutze ein Zalman Z9 Plus mit 20.5cm Breite, und da muss ich den großen der beiden Lüfter am Kühler ein wenig schräg stellen, um ihn Richtung Mainboard zu verschieben, ansonsten berührt er die Scheibe und zieht beim Schließen des Gehäuses das Lüfterelement mit. Der zweite der beiden Lüfter sitzt genau über den RAM.

Die Installation selbst wird zwar nur auf einem kleinen Zettel, dafür sehr ausführlich und auch für Laien verständlich beschrieben. Ich habe bei mir den Boxed Kühler eines Intel i7 3770K ersetzt und das gute Stück erst mal von 3.5GHz auf 4.5GHz übertaktet. Leider wird der Prozessor dann beim Stresstest mit prime95 doch im Schnitt ca. 107°C heiß, so dass ich das Experiment schnell wieder beendet habe. Bei 4.4GHz liegt das Temperaturmittel bei ca. 97-101°C; auch das ist mir sprichwörtlich zu heiß für den Dauerbetrieb. Die maximal empfohlene Temperatur von 90°C erreiche ich schließlich bei 4.3GHz.

Nicht übertaktet hält der Kühler die CPU übrigens selbst beim Maximum Heat Stresstest von prime95 auf unter 70°.

Momentan reichen mir gemütliche 4.2GHz, was ja auch schon immerhin 20% mehr Leistung bedeutet.

Der Geräuschpegel ist sehr leise und geht bei mir absolut im normalen Lüftergeräusch des Gehäuses unter.

Mitgeliefert wird neben schön beschrifteten Schrauben und mehr als ausreichender Wärmeleitpaste ein 4-fach Verteiler für die beiden Lüfter. Somit können sich noch zwei weitere 4-pin-Lüfter anschließen. Allerdings wird nur einer via PWM gesteuert.

4 persone l'hanno trovato utile

Joseph Edge

Great cooler that fits almost anything, looks great and runs quiet

Recensito negli Stati Uniti il 28 febbraio 2017

Intel OEM fan ran 48C, but this cooler brought it down to 26C on my i7 4790K at stock clock and moderate load. I did not rigorously benchmark the performance (others have done a fine job at that if you research it), but it has met/exceeded my expectations with anecdotal numbers.

Installation is not bad although I did have to do some of the process vertically before laying the case flat to finish the job. You must access the underside of the motherboard, which may add difficulty in some cases. It clears the RAM closely without touching it, but installing DIMMs in channel 1 will require finesse. The cooler is tall, so check the clearance between the CPU to the side of the case (mine fit without issue in a midsize ATX case with a 200mm side panel fan in place).

Una persona l'ha trovato utile

Hrishikesh Govindan

Fantastic Cooler!! Rated the "Best Cooler by Toms Hardware"!!

Recensito in India il 20 ottobre 2016

Fantastic Cooler for the price! This is as good it can get on air cooling!

I have an Intel Core i5 4670K which overclocked to 4.5Ghz put out some serious heat. Cooler Master Hyper 212X could not take it. Temps rose to 98C which can be very dangerous in the long run. I was on the fence about water or air cooling but went with air because of lot reports of pump leakage and ruining thousands of rupees of components. That sums up the "why this cooler" part!!
Source: [...]

Now on to the installation part and stuff to keep in mind before plonking down the cash-

(1) It needs an open back case with a requisite horizontal clearance of 167 cm in a PC Case/Cabinet, a full tower case might do but still check for manufacturer specifications.
If your case does not have access to the rear of the motherboard, you'd have to dismount the motherboard from the case and then mount the rear bracket on to the underside of the motherboard and then install the cooler.
Deepcool has a pretty good manual with pictorial description. Read it thoroughly before proceeding with the mount because this cooler weighs over 1800 grams(including the weight of both fans) and failure to mount it properly can break the motherboard. Experience and patience is of utmost importance here!

(2) Make sure you populate RAM slot 1 i.e closest to the CPU socket because this will be inaccessible after mounting this behemoth of a cooler. When installing this cooler make sure the 120mm fan(smaller of the two faces the rear exhaust fan of the PC case and does not hang over RAM slots because it would avoid any future RAM installation hassles. You may use the thermal paste included with it or use Noctua NT H1 for better results.

(3) Once the heatsink is in place carefully navigate as to which fan header should you use optimally. Don't mount the fans just yet, plug in the fan header in carefully first.

(4) NOW come the most patience-wringing back-breaking mind-f***ing task. Installing the fans on to the sides!! Take your time because the fan clips just won't stay on them(fans) when you try to install them on to the cooler. Good thing about them is their black borders are rubberized so they are dead silent. Now I am not silence freak but for those out there who want their rigs running quite then these fans drop as low as 300 rpm but can go up to 1470 rpm(as indicated on hardware info)

EDIT: Personal (read:pathetic) Experience with Overclockers Zone Kolkata:
I saw their listing on eBay, Amazon(not amazon fulfilled) and Snapdeal(out of stock). Tried contacting their local branch, sent emails around inquiring about this product because this is listed as Assassin whereas pictures whereof Assassin II. I was utterly disappointed with their customer care and ended up ordering from Cloudtail(at the time it was Rs.6075). Amazon FTW!!

3 persone l'hanno trovato utile

A. Morton

Brilliant product - cut CPU temperature in half.

Recensito nel Regno Unito il 2 gennaio 2016

Very glad I purchased this product - made a huge difference to my rig following a recent upgrade. CPU temperature has nearly been cut in half (compared to intel stock fan) and is almost whisper quiet - can barely hear the fans on everyday use. I removed the front fan from the heatsink (easy to do - just held on with clips) and installed this as a case fan to improve overall system temperature.
I would say to anyone looking to purchase this - make sure you have sufficient space in your case and around your CPU/RAM - this is a large heatsink! (Though lighter than I thought it would be).
Easy enough to fit (though getting cables connected around it after fitting was a bit of a pain so make sure you plan ahead). I'd also recommend a box of plasters on standby - the fins are quite sharp!

Una persona l'ha trovato utile

Mengfei.Feng

looks like it works with all kinds of boards

Recensito negli Stati Uniti il 22 maggio 2017

Yes, this is an expensive radiator or fan combo, but this offers a situation where you can say you get what you pay for. Very well designed, looks like it works with all kinds of boards, and included everything I could need for the process. Definitely the best experience I have ever had with a cpu cooler.This is probably the best you can do without going liquid cooling.